All posts by margueriteknight073

INstalled — Sq. D

Electrical Protection – at Least on most typical Surges .

I also have a 220 Volt Smoother : Smoother Power – Saves Boards

http://global220volt.com/product/tripp-lite-lr2000/

https://www.zoro.com/square-d-surge-protection-device-1-phase-120240v-hepd80/i/G4618844/

Building inspection process for a deck?

Hello all, I am in the final stages of designing a deck for my house using the IRC 2012 guide (some changes to 2015 IRC), and am about to submit for permits. This is the first time I have had to deal with a building inspector and permitting process so I am unsure how in depth I should be taking this. I have designed it adhering to code thus far, however I am now seeing areas were the code is a inconvenience. My thoughts are that I may be overestimating the level of scrutiny the inspector with apply, and how much leniency they give to slight inconsistencies. I am in New Jersey, and my district has adopted the 2015 IRC code. I feel as if when I am looking through pictures of decks online, I see so many code violations that would make my life so much easier. Such as…

-After looking through many documents, it appears you are quite limited in the amount of step down you can get from the door to the deck. When adhering to the allowable ledger bolt patterns and the band joist bolts, without completely changing the size of your joists, you are stuck with practically no step down. I am using 2×10 joists for the deck, and house band joist is 2×10, which by code would only allow a .75″ step. That is not great for snow in New jersey. Check out link to confirm

2015 IRC Deck Ledger Bolt Placement | ProTradeCraft

-Another area where I wish I has some room was the footings 5ft from the foundation rule. Unless you intend on digging your deck footings to the elevation of your house footings (unrealistic), than you have to space the deck off further than 5ft. This confuses me as the none of the maximum allowable joist overhangs in the code can reach span that 5ft distance. In my case this is not critical, as I am right on the edge of 5ft, however if I could cheat a little I would. Do inspections measure from the footer to the house? Pier to the house? Post to the house? Or, are they quite strict about the footer to the house distance?

-Stairs landing on concrete pads. Code says stairs must land on an area with footings of proper size and below frost. I have seen countless pictures of stairs landing right on concrete slabs, sometimes, just concrete blocks. ?

-How does an inspector, inspect your ledger attachments if he/she cannot access your interior band joist? Obviously, an owner w cannot demolish the floor to access the band joist? How does he very you are attaching the ledger to the right spots on the band joist (edge distances, no drill, no pass zones, esc)?

Thank you guys, I really need some advice here

Aint No Sheriffs Star…. lol

That Star of David thing….. thats something that also should be setting off alarms in peoples heads…..

Its not the fact that Trump is trying to tie Hillary to jewish cash…. but its the fact that Trump used that image that they got from a white supremacist post…… and reused it….

Do you want someone that dang stupid sitting in the white house ??? The guy is one ignorant sack of doodie.

Trump can say what he wants about the star….. but man… it doesnt take a 3 yr old to fiqure out what they are trying to say with the star and the pile of cash….

Maybe the US can get Mossad to deal with Trump…… in their own special way…. I know if I was in government… I would at least be considering that option…. no matter which side of the table I was sitting on.

Removing / replacing silicone caulk

We have a stainless steel sink (undermount) attached to a granite countertop. Over the years, the silicone caulk no longer creates a tight seal between the sink and the counter…therefore water is able to run down into the cabinet. The sink doesn’t feel loose, but it appears to have ‘sagged’ over the years. Should I remove the old caulk before applying new? I’m guessing the answer to that is yes, but what is the best method to remove the old caulk??

Thanks in advance for any advice!

My New GFCI wont reset! Please help

Hi, purchased this home bout year ago. It was built in 2005. Have one GFCI in unfinished basement. I tripped outside outlet that seems like connected to this gfci. Went downstairs and replaced gfci with new one as instructed there is two sets of black, white and bare so i tested the line and put set that gets around 120v in Line slot and no voltage reading on load. As soon as i turnes on breaker again i have red light came on solid. Please help!!

Honest Questions…

Looking for honest answers.

What was the real reason for introducing R410a (for widespread use) and why did it get this far with the high GWP?

To top it off, one of the proposed alternatives is already in R410a, so what caused them to go to all the bother of blending in the first place? I see may have to do with flammability, but the question stands… Why is the safety aspect less important now?

In my field this would be considered a “callback”…

Think coil drain is plugged, how to unclog

I have a Trane 4txc coil over my furnace. On the coil there are markings for P and S with PVC pipe coming out. The S PVC runs outdoors and the P appears to go into the all and connect at my kitchen sink drain. I noticed the outdoor S drain is dripping water. Does that mean the P is clogged? I am assuming P is primary and S secondary. My wife clogged the kitchen sink this morning but I plunged it and all of my drains are draining normal. Is it bad when the S pipe is dripping? And if so how do I unog the P?

Thanks

found the problem

Yuck. started having some drain issues awhile back, last few months got worse, few week ago started to back up in tub when washer emptied. dug up the line and ran pc plastic piping in the feel fro clog/break. hit a spot under house wall/crawl and thought was break in line catching debris.

was an issue there alright, can’t believe drain line worked, period. The big “coupling” was where I thought would be snag in line. cast iron going into plastic. Looks like someone ran heavy duty chemicals in there at one time and melted bottom of plastic.

Attached Images